How To Apply Prepasted Wallpaper: Proper Procedure Of Applying Prepasted Wallpaper

Proper Procedure Of Applying Pre-pasted Wallpaper

Wallpaper is a kind of paper that is applied to the wall & helps add color as well as texture to any room. The majority of the wallpaper is sold pre-pasted, which in turn means that you don’t have to deal with wallpaper adhesive. Applying wallpaper is not a difficult task but you can do this task on weekends that requires a lot of attention to detail. If you are looking to apply pre-pasted wallpaper, go through the below-mentioned procedure carefully & achieve the desired result of your work:

Step 1: Choosing Wallpaper

First of all, purchase a plumb bob and hang it from the ceiling. Mark the vertical line in different areas on the wall. If your walls or windows appear crooked in comparison to these lines, then take into consideration a random wallpaper pattern in order to make sure that the edges and corners aren’t noticeable.
Make sure that there is sufficient room to view your pattern. Generally, large prints don’t work in small rooms, due to the reason that they make them feel smaller.
Select small prints as well as light colors in order to make your room feel larger. Small prints represent the size of the room, while light colors reflect light, which will help add to the spacious feeling.
Choose for wallpapering just one wall with any pattern in order to make a statement wall. It is better to use a wall without windows and other fixtures in this case.
If possible, buy a wallpaper from a wallpaper company or wall covering company, due to the fact that this will let you to inquire about the best methods as well as tips for using it. You can call the store if you have any questions throughout the process of applying the wallpaper.
Save the run as well as dye lot numbers that are written on the back of your wallpaper. If you need to order more, then they may be able to complement the color to the exact printing that you used previously.
Read or go through the instructions carefully that come with your wallpaper. Each paper is, to a small degree, different. When in doubt, use clearly defined or identified directions instead of general directions for wallpapering.

Step 2: Prepping The Walls And Supplies

Buy or rent a complete set of supplies in accordance to the list of things below.
Visit the wall covering shop and rent a basswood table, if you can. To make your own, place a 3 by 6-foot (0.9m by 1.5m) piece of three-fourths inch (1.9cm) plywood on top of two sawhorses. Sand the corners of the plywood in order to avoid tearing. Basswood as well as plywood are like a self-healing mat, which allows you to cut into the surface of the paper, with the help of a utility knife without ruining the paper.
Ask someone to help you apply the wallpaper for the best results. Large pieces can be moderately unwieldy.
Mark the plumb line & then hang sections of wallpaper. You need to make a mark every six inches (15cm) or so, in order to make sure you hang a sheet to be completely level. Don’t trust ceilings, floors, trim or windows, as majority of them are hung without being perfectly level.
Take out all the furniture items from the room, or as much furniture as you can. Protect the floor by covering it with drop cloths. The water as well as paste can drip off the table and onto floors.
Prepare your walls well in advance. Apply patching compound and sand it if in case there are holes. Wash the wall using the trisodium phosphate (TSP) or a TSP substitute.
Improve the application of your wallpaper by spreading a layer of acrylic undercoat, called sizing, to the wall and then allow it to dry overnight. You can also prep as well as seal your walls by applying a coat of primer. For outstandingly uneven walls, apply special “liner paper” over them before pasting wallpaper.

Step 3: Wetting Pre-pasted Wallpaper

Take a perpendicular or an upright strip of wallpaper. Trim it to the length of your wall, adding 4 inches (10cm) of extra space, or 2 for the top and 2 for the bottom.
Move the piece smoothly from bottom to top, inside out. This means the pre-pasted side, generally white side, should be toward the outside.
Take a water tray & fill it with room temperature water. Put it down at the bottom end of your worktable.
Sink or immerse the roll of wallpaper in the water tray. Soak it for nearly 30 seconds, or the time usually recommended by the manufacturer.
Roll out the paper onto your worktable & make sure that the patterned/colored side be facing up.
Fold the ends, to a small degree, inward toward the pasted side. They should not be creased, simply coerced moderately in toward the pasted side, called “booking.”
Allow the wallpaper sit for 2 to 5 minutes. During this time, the wallpaper become or make larger or more extensive. Laying the paper too soon will cause it to stretch on the wall and create gaps.

Step 4: Hanging Pre-pasted Wallpaper

Take hold of & lift the wallpaper off your worktable making sure that the pattern is right side up.
Align as well as apply the top half of the paper sheet to the wall. Use your plumb marks on the wall in order to line it up. Then, leave nearly two inches (5cm) of extra paper above the trim, which you will remove later.
Move the paper smoothly into position as needed. The size on the walls should allow you to move it to an exact position.
Use a wallpaper smoothing brush or tool when it comes to getting rid of bubbles. Brush the bubbles out in the direction of the sides. Repeat as long as the wallpaper is smoothed to the wall.
Repeat the same process with the bottom half of the strip. Always smooth from top to bottom as well as from the center toward the sides.
Wet a sponge as well as wash off excess paste from the patterned side of the wallpaper, as necessary.
Trim the wallpaper by taking hold of a putty knife flush with the trim. Cut with one clean motion in opposition to the top edge of the putty knife using a utility knife. Keep your utility blade as straight as possible as you cut. Restore the blade after cutting the trim off two pieces of wallpaper. Sharp blades are important in order to avoid tearing.
Apply the remaining of your wallpaper in a same way. Make sure you align it using the plumb line and with the previous strips of wallpaper. Pay attention to manufacturer instructions on how to match up the pattern.
Apply the wallpaper over light switches as well as other features. Then, trim from the center of the fixture toward the corners. Trim the paper with the help of utility knife and putty knife.