How To Secure Lamp To Table: Step By Step Instructions Of Attaching A Lamp To Table

Step By Step Instructions Of Attaching A Lamp To Table

It is simple to fix household lamps that aren't functioning properly. The plug and cord are straightforward and affordable to replace, and are accessible at any well-stocked hardware or electrical store. A light socket can be installed with same ease. You should be able to select a replacement socket that matches the color tone of the original socket because replacement sockets come in a variety of finishes. Zip cord, also referred to as Type SPT lamp cord. The majority of lamp applications are suitable for the #18 size. Although zip cord comes in a variety of hues, the most popular ones are black, brown, white, and transparent. Match the lamp stand's or the wall's color with the outlet's chord. Although 6 feet is the usual length, you can use however much cord you need to connect the lamp to the outlet. Calculate the length of the cord (including the cord that is concealed in the light) and add 1 foot for attachments to the socket and plug as well as for slack to determine how much cord to purchase. It is preferable to have a sufficient length of cord in terms of safety and appearance than to use an extension cord to make up for a short one.

Step 1: Disconnect The Power & Remove The Bulb

Pull the plug from the wall outlet. Never use any machinery while the lamp is connected. Remove the shade, unscrew the bulb, and press the socket shell at the switch to separate it from the socket cap and the cardboard insulator. Do not pry the socket apart with a screwdriver if you intend to reuse it. Pull the socket as far from the shell as the connecting wire will allow. If you still don't have enough wire, pull the cord up from the bottom of the light for more slack.

Step 2: Remove The Socket

Remove the cable wires from beneath the socket's terminal screws by loosening the screws. Slide the old wire out, then feed the new wire through from one end to the other if the lamp is small and the cable passes through in a straight line. Do not pull on an old cord if it presents any resistance at all. To make removal easier, see if you can disassemble the lamp. Additionally, ensure that the cable is knotted to prevent it from being yanked out at the base.

Step 3: Cut The Power Cord

Cut the cable approximately 12 inches from the lamp base, slice the two conductors apart, and peel about an inch of insulation from the ends to remove the tight cord. Apply the same technique to the new cord's beginning. Twist the ends of the cord's new and old conductors together, then fold the twists flat. Wrap the splice with electrical tape. Push the new cord in from the bottom while simultaneously pulling the old cord out from the top of the fixture. Cut off the old cord once the new cord is long enough to pass through the top.

Step 4: Remove The Insulation

Split the end of the new cord once it has passed through the lamp so that the conductors are separated by about 3 inches. Twist the strands of each conductor together after removing about 3/4 inch of insulation from the ends of each using a wire stripper tool. When you remove insulation, take care not to nick any strands.

Step 5: Connect Wires To The Terminal

Each wire's twisted end should be bent into a clockwise loop, which should be placed under the socket's terminal screw and wrapped around the screw in a clockwise direction. screw terminals firmly. The clockwise loop will pull the wire closer to the screw head as each screw is tightened. (A loop made in the other direction tends to weaken wire.) Use diagonal cutters to remove extra bare wire. No loose strands or bare wire should be visible; all insulated wire needs to be hidden underneath screw heads. Unscrew the terminals, take out the wires, and reconnect them if any exposed bare wire is visible past the screw heads.

Step 6: Attach The Insulator & The Plug

Place the socket shell over the insulator, then place the socket over the shell and insulator. Then secure the socket and shell into the cap. Attach a quick-clamp plug to the cord's other end. Put the cord's end in the slot on the plug's side and depress the lever at the top. To form an electrical connection, metal prongs inside the plug will rip through the insulation of the cord and pierce the copper wires. If using a screw-type plug, prepare the wire ends the same way you would for a socket screw connection before knotting them. Before tightening the bare end under the screw head, wrap each wire around the prong of the plug. It is more difficult to loosen connections by pulling on rope when there are knots and loops because they prevent wires from unintentionally touching one another.

Step 7: Reassemble The Lamp

Before plugging in the light, tighten the wires under the screw heads and cut off any extra uninsulated conductor.