How To Replace Fascia Board With Drip Edge: Step By Step Process To Replace Fascia Board With Drip Edge


General Overview

Fascia boards are vulnerable & prone to water damage, which as a result leads the wood boards to rot that can become loose and are unpleasant to look at. If you are looking for fine home makeover, then you need to repair or fix your fascia boards. Fascia boards run parallel to the plane of the horizon underneath a roofs edge and can be composed of wood or sheet metal. These boards are placed or fixed in segments and the seams should be arranged at the rafters which helps safeguard the ends from water damage. If in case the paint is peeling from the fascia board, but the wood is in good condition, then it is important to sand as well as repaint your boards. If you notice indications of rot, then you will need to cut those sections out at the rafters before replacing them.
Fascia board is a kind of board that is used to take hold of your gutters in place and helps in protecting the edges of your roof. These sections are exposed to a lot of moisture and with the passage of time can start to rot. The fascia is regarded as one of the long wooden boards that runs parallel to the plane of the horizon on the edge of the roof. Generally, the size of the fascia board is either 2×8 or 2×6. This board helps in connecting the gutters to the roof truss. If there is no wood in this spot, that’s likely due to the reason that your fascia boards are protected with a vinyl or aluminum cap in order to match your gutter system. Homes with no fascia boards at all are very rare. The state of being without or not having enough of a fascia board is generally against building codes and should be corrected in order to safeguard your home.

Step By Step Process Of Replacing Fascia Board With Drip Edge

Pulling apart or dismantling fascia boards as well as their drip edges generally involves removing nails and cutting replacement materials. When it comes to have an extensive roofline, it may be better to work at the top of scaffolding instead, and move it around the house in order to complete the job. Go through the below-mentioned steps carefully in order to replace fascia board with drip edge:
  1. Mount A Ladder Or Scaffold: First of all, climb or move up on to a ladder or scaffold. Pry up the metal spikes that takes hold of the gutter to the roof. Lower the gutter but make sure to take the assistance from someone in order to avoid twisting it if you are planning to reuse it.
  2. Cat’s Paw Or Nail Puller: Pry up with the help of a cat’s paw or nail puller the nails in the drip edge’s extremity or base flange where it joins the fascia board. Take the drip edge’s top flange out from underneath the shingles and with utmost care keep it to one side for potential reuse.
  3. Pry The Fascia Board: Pry the fascia board off the rafter ends as well as the sides of the soffits, taking the nails out, and get rid of if you are looking to replace it.
  4. Measure, Mark And Cut Replacement Fascia: Calculate or compute, mark as well as trim replacement fascia from lumber or aluminum, usually known as pressure-treated wood. Fasten, using nails, the midpoint of each length of fascia onto a rafter end, before nailing out in either direction, securing the fascia to the rafters and soffits. Place or fix the gutters by lifting them but make sure to take assistance from someone and nailing their spikes into position.
  5. Install The Gutters: Slide or move the wide flange of the drip edge underneath the shingles as far as possible. Given a range of shapes as well as designs, read or go through the manufacturer’s instructions in order to find out whether to hold the flange in place using roofing cement applied atop of the drip edge or by nailing it to the fascia. You also may calculate, mark as well as cut replacement drip edge. Let the narrow flange to wrap over the gutter edge in order to safeguard the overhang or joist from moisture.
Connect with GetRit GetRit.com Furniture Facebook GetRit.com Furniture Twitter
Copyrights (©) 2024 GetRit.Com   All Rights Reserved