How To Remove Gel Stain From Fiberglass Door: Different Ways Of Removing Gel Stain From Fiberglass Door

Gel stain is used on many materials, which may also include fiberglass and wood, in order to provide a clean finish with a slight sheen. However, if you apply the gel stain improperly, then it is highly possible that it can create a noticeable as well as unattractive raised texture. Stripping is the only way when it comes to fixing raised gel stain after it has dried. The extent of the stripping needed is entirely dependent on whether the gel stain was sealed or not. The majority of people are unaware that gel stains will permanently damage the fiberglass door. Therefore, you should know how to get rid of the gel stains from fiberglass doors in order to keep away from this costly as well as irreversible mistake.

Different Ways Of Removing Gel Stain From Fiberglass Door

Gel stain is regarded as a thicker stain that is usually used to stain vertical surfaces including doors and walls. This is due to the reason that the stain will not drip and run like liquid stains. When you stain fiberglass with gel stain, the stain will not soak into the fiberglass as the stain does with wood. Therefore, it is simpler to get rid of the stains from fiberglass doors. Always use gloves as well as goggles when using chemical strippers in order to safeguard your skin and eyes.

Way 1: Rubbing Alcohol

Blot the gel stain with the help of a clean rag or cloth. Test to find out whether the stain is removable or not by dabbing just a small amount of rubbing alcohol onto the gel stain before blotting using a cleaning cloth. If it is not removable, then skip this step. If it is removable, then you can use Rubbing Alcohol in order to clean stains from fiberglass doors. Spray the alcohol on the gel stain, before wiping away with the help of a clean rag. Repeat as long as the gel stain is removed completely from your fiberglass door surface.

Way 2: WD-40

Another way is to use WD-40 when it comes to removing gel stains on fiberglass doors. Spray WD-40 onto the gel stain, before wiping away with the help of a clean rag. Repeat as long as the gel stain is eliminated entirely from your fiberglass door surface.

Way 3: Mineral Spirit Or Turpentine

You can also use a soft cloth having the mineral spirit or turpentine. Use a clean paint dry cloth in order to cover & protect the stained area of your fiberglass door before applying either mineral spirits or turpentine onto the stains on your fiberglass door surface. Allow it to soak in for at least 30 minutes, before wiping away using another cloth.

Way 4: Thickened-down Paint

Another important method to get rid of gel stain from a fiberglass door is to use thickened-down paint. Apply the thinned down gel stain onto the gel stain that is present on your fiberglass door surface, before allowing it to sit for at least 30 minutes. Wipe away the excess with the help of clean cloth as long as it’s gone.

Way 5: Sanding

You can also get rid of the stained gel coat from fiberglass doors by sanding lightly. Always make sure to start with the lowest grit (80-grit), and try to sand gently, delicately, or softly. Start from one side of the gel stain, before working in small circles and going in the opposite direction as long as you have removed as much gel stain as you possibly can. You will need to apply some pressure in order to get rid of all of the gel stains from your fiberglass door surface. So, try to apply as much pressure as you can when you’re sanding the gel stain.

Way 6: Heat Gun

You can also get rid of the gel stain on fiberglass doors using a heat gun. If your gel stain is still visible after trying all the above-mentioned ways, then you can try using a heat gun (or blow dryer) in order to slowly warm up the area where you have applied the gel stain to your fiberglass door surface. Do this gently and in very small circles around the gel stain in order to prevent over-heating the gel coat on your door. Make sure not to get too close, otherwise, you will risk damaging your fiberglass door.