How To Keep A Rug In Place On Wood Floor: Three Easy Ways Of Keeping A Rug In Place On Wood Floor

Three Easy Ways Of Keeping A Rug In Place On Wood Floor

If you don't secure an area rug properly, then it is possible to have a significant safety risk for your family. One of the main reasons for area rugs to slide on a hardwood floor is due to the fact that there's no grip betwixt the floor and the rug. There are numerous ways in order to keep your rugs from sliding on hardwood floors, and the four of the most effective ways are mentioned below:

Way 1: Use A Non-Slip Rug Pad

1. Measurement: Before going out to buy a rug pad, it is important to know your rug’s dimensions. With the help of a tape measure, calculate & estimate the length as well as the width of the rug. If there are edges in your rug, then leave them out of the measurement, due to the fact that the rug pad won’t need to protect them.
2. Purchase The Right Rug Pad: Non-slip rug pads are available at any home improvement or carpet stores. If you are not able to find a rug pad that exactly matches your rug’s size, then buy one that has enough excess in order to luxuriously and snugly fit your rug. It is best to get a rug pad made of vinyl materials such as plastic or rubber that might discolor wooden floors.
3. Lay The Pad Against The Rug: If the rug pad is larger in comparison to your rug, then trim it to fit. Put, lay, or stand one of the rug pad’s corners up alongside the rug’s corners, keeping an inch(2.5 cm) of clearance on either side. For each side where the rug pad clings tightly, use a marker and a ruler in order to draw straight lines an inch (2.5 cm) away from the rug’s edge.
4. Trim The Rug Pad To Size: With the help of scissors, trim along the lines that you have traced in marker. General crafting or kitchen scissors will work ideally. It is important not to catch the rug as you trim, you need to take the rug pad away from the rug if in case you’re worried about cutting the rug.
5. Apply Double-sided Carpet Tape To The Rug: Now, trim four strips, one for each side of the rug, examining them so that there’s nearly an inch or two (2.5 - 5 cm) of clearance on each side. Push on the strips of tape. While pushing tape on the perimeter of the rug is enough, you can trim a few extra strips for the center of the rug if you are looking for a better grip on the rug pad.
6. Remove The Protective Backing: Carpet tape generally has a plastic backing protecting one of its sides, which in turn helps prevents it from sticking to your hands as you spread it and makes sure it’ll stay sticky when it needs to be. Just take off this plastic covering when you are ready to stick the rug pad on.
7. Apply The Rug Pad: Put down the rug pad on top of the rug, ensuring to center it. Apply pressure where the rug pad joins or connects the carpet tape in order to make it stick. You may have to make a few passes so that you get proper grip.
8. Lay The Rug On The Floor And Test It: Lay the rug where you are looking to leave it. With the help of your foot, apply pressure on the rug, & try to push it forward, backward, and side to side. If you have applied the rug pad accurately, then the rug should definitely stay in place. If the rug still moves, apply the rug pad again. It is also possible that you may need a rug pad of a different material, which is totally dependent on your floor's finish.

Way 2: Hot Glue Or Caulk

1. Flip The Rug Over And Apply The Caulk: According to the width of the rug, squeeze out the strips of caulk. Put down the strips at intervals of nearly 6 inches (15 cm) for the best grip. Acrylic-latex caulk is regarded as one of the best options for this purpose. On the other hand, you can use a hot glue gun in order to layout grippy strips, the process will be mostly the same.
2. Let The Substance Dry: Keep the rug in a well-ventilated room without any disturbance. If you have children or pets, make sure to close the door so that the rug isn’t disturbed. Wait as long as the caulk or glue is completely dry. If the caulk or glue is not dry fully, then it will cause the rug to stick to the floor and damage it.
3. Flip The Rug Back: As soon as the caulk or glue is completely dry, lay the rug down on the floor. If you want to test its grip, just put down your foot on it and try to slide it around. The dried caulk should keep it away from slipping around. If the rug doesn’t have sufficient or adequate grip, you can flip it over as well as add more strips of caulk with smaller spaces betwixt them.

Way 3: Use Velcro Strips

1. Mark The Rug’s Place On The Floor: Mark the rug's place as it will be very helpful in aligning the velcro on your floor considering the fact that they won’t be easy to move once placed. With the help of a light pencil, mark the outlines of the rug’s corners.
2. Turn The Rug Upside Down: In order to make it very simple, you can overturn the rug right over your markings.
3. Cut Strips Of Velcro Into 2 Inches (5 Cm) Sections: You can purchase velcro in strips at any home improvement store, generally on a roll. There needs to be both the hook as well as the loop sides, one is rougher to the touch in comparison to the other. Trim 4 strips of the soft side as well as 4 strips of the rougher side.
4. Peel The Protective Backing Off Of Each Strip: This plastic backing protects the velcro strip’s adhesive properties. After taking this off, put down the velcro strips on the ground, the adhesive side should be pointing upwards.
5. Stick A Soft Velcro Strip In The Corner Of The Rug: Lay each strip a few inches away from the corner, adhesive side positioning towards the rug. Apply pressure to the velcro strips so that they will stick. Repeat this for each & every corner of the rug. Be extra cautious while placing the velcro strips, as they’ll be hard to get rid of once glued on.
6. Stick The Rough Velcro Strips On The Floor: Using the placement of the velcro on the rug as well as the pencil markings on the floor, align the velcro. Take your time & apply the velcro to the floor, the adhesive is strong enough that it is not possible to adjust the strips without entirely ripping them from the floor. They will likely lose their adhesive property before leaving glue on your floors.
7. Flip The Rug Back Over: Line up or arrange the Velcro strips together before applying pressure to each corner of the rug. The rug will now be firmly held to the ground.