How To Install Shiplap On Wall: Step By Step Instructions Of Installing Shiplap On The Wall


Step By Step Instructions Of Installing Shiplap On The Wall

You can attach or secure Shiplap planks to walls either vertically or horizontally. You just need to nail through the drywall straight away into wall studs. You can use construction adhesive when you are looking to install the shiplap on ceilings or over other surfaces, until & unless they are in good condition. Simply finish-nail the panels in place in order to take hold of them while the adhesive dries. Trim corners, ceilings, as well as floors with smaller 1-inch-by-4-inch boards, which are entirely dependent on your style preference as well as skill level. A compound miter saw will be very helpful when it comes to piecing together planks and trim with the help of a mix of butt joints, miter joints, and bevel joints.

Step 1: Prepare Walls

Before starting the installation process, first of all, you need to pull out everything from the wall including any nails. Using a putty knife, lightly pry & remove baseboards, crown molding, as well as trim. You also need to pull out wall plates & outlet covers. Before installing your shiplap boards, it is important to open your boxes and allow the flooring to adapt or become used to the room temperature as well as moisture for nearly 48 hours.

Step 2: Paint

Shiplap has a signature gap betwixt the joints that allow the wall color to show through, therefore, it is important to paint the wall where you are going to install the shiplap, with either the same color of your shiplap or contrasting color. Paint or stain unfinished shiplap boards & then attach or secure them to your wall.

Step 3: Measure Wall

After getting to know about the installation process of shiplap, now it is time to figure out how much shiplap you will need. Discover the square foot of the wall that you are going to cover by multiplying the length of the wall with its height. Add 10 percent to your total in order to account for any waste. Divide the height of the wall with the width of the shiplap boards. Position any boards you will have to cut horizontally at the underside of the wall.

Step 4: Mark Vertical Studs

When you nail your shiplap boards to the wall, it is best to secure them to the vertical studs of your wall. Use a stud finder when it comes to determining where your wall studs are. The majority of the studs are usually 16 inches or 24 inches apart. Mark each stud using a vertical chalk line when it comes to easy identification.

Step 5: Make A Guideline & Follow Them

Your finished wall will simply be as straight as your first row. With the help of a level, draw a straight horizontal line from one end to the other end of the wall. Make sure your guideline is straight by positioning your level at different points on the guideline. Align the top edge of the underside row of boards with the horizontal guideline you created. Make sure your board either lays on or overlaps the vertical chalk line that you made in order to identify the studs in the wall. You can secure your shiplap boards with construction adhesive or nails or both.

Step 6: Attach First Row Of Shiplap

Position a nail through the top as well as the bottom of each shiplap board where it crosses a stud. Use adhesive in order to glue the board down first or you can take assistance from someone in order to hold it in place.

Step 7: Place Nickel Spacers

Before attaching or securing the next board, position a nickel every few feet betwixt the underside board and the board above it. This will help you in giving an authentic shiplap look. After securing a board, remove as well as reuse the nickels as spacers betwixt rows.

Step 8: Stagger Cuts & Attach Matching Baseboards

Cut and position boards to stagger cut ends from row to row. Repeat as long as the wall is complete. If two boards connect or link up at the same stud, position the first piece halfway onto the stud and nail. Start another piece on the same stud & cut to fit, if necessary. Repeat as long as you reach the end of the row and never overlap boards. Add matching baseboards as well as molding with the help of finishing nails. Floors are hardly level. Use trim in order to cover any gaps betwixt your wall and the floor.
Connect with GetRit GetRit.com Furniture Facebook GetRit.com Furniture Twitter
Copyrights (©) 2024 GetRit.Com   All Rights Reserved