How To Install Recessed Lighting With Attic Access: Recessed Lighting Installation With Attic Access From Attic


Recessed Lighting Installation With Attic Access From The Attic & Main Floor

If you are looking to entirely change the look of any room in your home, then the best option is to Use recessed lighting. The design should be the first priority, regardless of whether you are looking to remodel or simple change your lighting. If you are looking to do something with recessed lighting, first of all, determine the kind of lighting that you want to use, how to present it, and whether you have enough space or not in order to accommodate your plans. Before installing the recessed lights, it is important to mark the holes where they will go. From the main floor, you can cut your holes with the help of a keyhole saw, or from the attic, using a power saw. This will help to make sure that the circuit that your recessed lights are on can handle the extra wattage they will be using. You may look to hide or conceal your under cabinet light.

Install Recessed Lighting With Attic Access From The Attic

  • Switch Off The Circuit Breakers Or Fuse Boxes
    First of all, switch off the electricity in the room where you are going to work before you start. Switch off the circuit breakers or fuse boxes by simply turning a switch in their off position. Before touching anything, make sure to use your ohmmeter in order to check that the electricity is off. When replacing a light, it is important to shut off the light switch that is connected to the light.
  • Assign Specific Location For Each Opening
    Assign a clearly defined or identified location for each opening in order to make sure that there is enough room for all of your lights. Six inches should be the minimum distance that they should have betwixt each other. Lighting fixtures are available with a template so that you can use them. Wearing work gloves, a mask, as well as a protective clothing, including long sleeves and long pants can safeguard you from harmful damages. Due to the reason that you will be cutting into drywall and using sharp tools.
  • Make A Hole Using A Drill In The Middle Of Each Outline
    In the midway of each outline, you drew on the ceiling, make a hole using a drill. When making a hole, make sure that nothing is in your way. Keyhole saw hole attachment on your drill are all best options when it comes to cutting around the outline you drew.
  • Run The Lighting Cable
    In the attic, you need to run the lighting cable. From the power source to the switch box, NM-B (non-metallic) wire is what you will need. At least a foot of extra cable is also suggested for easy installation. If you have a circuit breaker or fuse box, run the cable to that location, & clamp it in place. You’ll need to get rid of 0.5 inches of insulation in order to expose the wiring underneath.
  • Securely Connect The Wires To Their Corresponding Colors
    In order to get rid of the insulation from each of these wires, strip 0.5 inches of it with the help of a wire stripper. Securely connect the wires to their corresponding colors with the help of UL-approved wire connectors. Wires of the same color need to be matched, as should those of the same color. You can use ground wire as a green or bare wire. Close the circuit box after you carefully insert the wires.
  • Use The Spring Hooks On The Connectors Inside The Housing
    Create a hole from below as well as slide a small can light through it from the attic, before sliding it into the hole you created from below. Verify that the can’s clips are firmly attached or secured to the ceiling if there are any clips on the ceiling. You can use the spring hooks on the connectors inside the housing if you don’t have a cable. Make sure that all the wiring is connected before you return to the main room. Plugin the light bulbs before switching the power back on in order to make sure you can check that if it still works.

Install Recessed Lighting With Attic Access From The Main Floor

  • Switch Off Your Main Circuit Breaker Or Fuse Box
    Firstly, switch off your main circuit breaker or fuse box. You don't need to switch off the circuit breaker of the entire house, but simply the rooms you are rewiring. In spite of the fact that the power has been switched off, you should still check the wires in order to make sure that the power has been switched off. Shut off the position of the wall switch.
  • Use The Template That Come With The Fixtures To Mark The Opening
    You can also use the template that are available with the fixtures in order to mark the openings. Use a stud finder to ensure that there is no joist in the area where you are going to install the light fixture. It is important to wear protective clothing, a mask, as well as work gloves before you begin. A 0.25-inch hole should be drilled in the center of the opening you drew. You will need to check the attic when it comes to obstructions.
  • Cut The Hole Where You Drew The Outline
    Cut the hole where you drew the outline with the help of a keyhole saw. An attachment for your drill can also make the installation job easier. From the power source to the switch box for the first hole, you need to run the NM-B wire. Keep an additional foot of cable on hand in order to make wiring easier.
  • Run The Cable To The Circuit Breaker Or Fuse Box
    You need to run the cable to the circuit breaker or fuse box before clamping to the box to complete the circuit. In order to open up the wires beneath, strip the wires of their insulation by at least 1/2 inch. To get rid of the 1/2 inch of coating from each individual wire, perform the same procedure as above.
  • Match Up The Colored Wires To Make Sure That They Are All Connected Together
    You will need to match up the colored wires in order to make sure that they are all connected together. On the other hand, the ground could be a bare wire or be protected with green insulation. Wire connectors need to be UL-approved. If you have a box, then you need to fold the wires inside and close the cover. Make sure that the clips do not stick out of the sides when you are pushing the housing into the ceiling spot from below.
  • Push The Light Into The Housing
    It is important to push the light into the housing as long as it is securely fitted in place. Trigger the clips by pushing them up and out as long as they click in place. You can place or fix the light trim by hooking the springs to it. Examine that it works properly by putting in the right size light bulb.
Connect with GetRit GetRit.com Furniture Facebook GetRit.com Furniture Twitter
Copyrights (©) 2022 GetRit.Com   All Rights Reserved