A piano hinge is a sort of hinge that has leaves that are all the same size and is held together by a central hinge pin. Piano hinges are named after their use with piano lids, although they can also be used for any furniture and equipment that needs the hinge to open to a minimum of 270 degrees. They are also perfect for projects where heavy wood and repeated use are factors. A piano hinge has a length that is really longer than the standard ones. This kind of hinge typically measures six inches wide and about six feet long. Even lengthier versions of them exist. Actually, none of these are designed for the piano. There are numerous additional domestic uses for it as well. But, you will have the most adaptability and be able to use your piano in a new way when you attach it to it. But, how do you mount a piano hinge on a bench seat?
Installation Process Of Piano Hinge On Bench Seat
Although the procedure is a little challenging, installing a hinge won't require you to be an expert woodworker or musician. This do-it-yourself project would be easy to finish if you had the right materials and techniques. Fortunately, you have arrived at the proper location. This is because this article contains all the necessary information and is accurately written. You just need to pay close attention to each step, and you'll soon learn how to attach a piano hinge to a bench.
Supplies Needed
- A Borah Edge Guide
- A Circular Saw
- Piano Hinge
- Some Screws
Step 1: Mark The Place Where You Want To Put The Piano Hinge
Prior to installing the piano hinge, you must mark the location. Raise the bench a little in this situation. You'll have more working flexibility as a result. Two points should be marked; one will be attached to the hinge and the other will be simple to remove when needed. At one location, drill two holes for the screws, and after that, screw the piano hinge to them. Your hinge will be kept firmly in place. The top side of the bench can have one hole, and the bottom should have the other. The use of it will be more practical.
Step 2: Use The Circular Saw To Make A Few Cuts
- You must now use the circular saw if you have finished marking it off. Press the circular saw slowly and lower into the wood surface to turn it on. If you've dug down far enough, return to the designated places. Keep it steady and move it to the designated spot. Now make a few cuts with the saw along the plywood's line of cut. It can be taken down from the wall or table with the saw as well. The plywood needs to be fixed in place after that using the clamps.
- It would be best for you to utilize a sharp blade while using a circular saw. It is not recommended to use the circular saw's included blade. Then, to improve the saw's efficiency, you must swap it out for another one.
Step 3: Select One Of The Sides Where You Want To Install The Piano Hinge
- The opening in the box needs to be cut out using a circular saw. You will need to use something sharp to cut the edges of the box apart because they will still be joined.
- Choose the side on which you wish to attach the piano hinge if the box shape has been totally removed. Choose a side, and then position the hinge saw there. Finally, cut it. The hole created by the hinge saw during the cutting process is large enough to accommodate the piano hinge. The piano hinge must now be inserted into that hole as the next step.
- The entire wood box will be held by a lengthy hinge that will be attached with a few screws. So, be sure to avoid leaving any screw holes. Wait a second! You must drill the holes, am I correct? Let's check it out in the next phase! Put in the hinges. It's time to put the hinges in place. Again, use a screwdriver and screws to ensure they are securely fastened.
Step 4: Make A Pilot Hole To The Center Of The Hinge
You must drill the holes in accordance with the hinge's existing holes. Don't leave any of the holes, as I've said before. In this situation, a form of pilot hole to the hinge's center can be made using an automatic center punch. You may also use a large spit, but this method is preferable because it works so quickly. Use a temporary screw if necessary to keep the hinge in its proper place.
Step 5: Start Drilling The Screws Into Every Screw Hole Of The Hinge
Take a drill now, and begin drilling screws into each and every hinge screw hole. Keep the hinge steady and make sure all of the screw holes are covered. Check everything thoroughly to see if any holes were left after finishing from one end to the other. If everything is in order, use the handsaw to once more separate the front and sides. Check the opening once more; everything should now flow easily.