Steps To Replace Different Components In A Maytag Dryer
Once you open the door of your Maytag dryer, after the completion of a dry cycle and if you still find your clothes as wet as they were at the start of the dry cycle, then it specifies that your appliance is no longer producing heat. In order to assist you to identify the fault behind your non-heating dryer, here you will find a list of faulty components that prevent a dryer from generating heat. Before starting the repairing process, make sure to disconnect it from the wall or switch it off at the circuit breaker. Also, protect your eyes as well as hands by wearing safety equipment during a repair process.
The Thermal Fuse
The Maytag dryer is assembled with a safety device, which is commonly known as a thermal fuse. In case your dryer starts to overheat, the thermal fuse will turn off the power to the drive motor, which means the safety component needs to prevent your dryer from causing a fire. If in case the thermal fuse is malfunctional, it can prevent your appliance from generating heat. In order to repair your dryer, you will need to replace the thermal fuse.
- To fit the dryer’s large, rear panel, move your dryer away smoothly from the wall. Detach all the screws attaching the panel to the dryer. As soon as the screws are detached, rigorously upraise the panel of the dryer and keep it somewhere at a safer place.
- Find out the faulty thermal fuse, and disengage the wires running to it. Untie the mounting screw grasping the fuse in place, and eliminate the component from your dryer.
- Take hold of the new thermal fuse and secure it to your dryer with the help of a mounting screw that you detached earlier.
- Restore the wires, and put back the dryer’s large, rear panel. Connect your appliance to the wall or switch it on at the circuit breaker and drive your appliance back so that it is perfectly positioned near the wall.
- Check your repair out by putting a load of wet garments into your appliance, and moving them through a dry cycle.
The Heating Element
The heating element in your Maytag dryer is composed of a metal chamber and coils. As soon as you switch your appliance on, the electricity moving to the dryer heats up the coils, which in turn, also heats up the air running through the component’s metal chamber and sent into the appliance’s drum. If in case the heating element is defective, the coils won’t get hot, which means the air circulating through the drum will not be able to dry your clothes. When a heating element is faulty, you can frequently find out the problem by carrying out a visual inspection. If the coils are burnt out, then it is necessary to replace the component.
- Take out your dryer forward, and slide to the back of the appliance. Detach the screws grasping the large, rear panel onto the dryer frame and upraise the panel up and off your appliance.
- Before you take out the heating element from your dryer, disengage the wires from the high limit thermostat, which is situated on the side of the heating element. As soon as the wires are disengaged, eliminate the thermostat from the heating element. Then, disengage the wire moving to the heating element.
- Remove the screws attaching the heating element to the appliance, and take the faulty component out of the dryer.
- Hold the new heating element, and secure it to the dryer with the help of mounting screws. Put back the high limit thermostat, and restore the thermostat and heating element wires.
- Fix the rear panel again and connect your appliance back into the outlet. Start a dry cycle in order to make sure that the new heating element sorts out your appliance’s malfunction.
The Cycling Thermostat
The dryer’s cycling thermostat usually calculates the air temperature in your appliance. As soon as the temperature in the drum gets too hot, the thermostat switches off the heating element, and as the drum starts to cool down, the thermostat switches the heating element back on. If in case the cycling thermostat is not working properly, the dryer will not heat up. Then, in this situation replacing the thermostat is the best option.
- Start your repairing process by taking your appliance away from the wall and detaching your dryer’s large, rear panel.
- The cycling thermostat is secured to the dryer’s duct casing, which is situated near the base of the appliance. As soon as you locate the component, disengage the wires moving to the thermostat terminals. With the wires removed, untie the mounting screw that attaches the thermostat to the duct casing. Take out the faulty part from the dryer.
- In order to install the new cycling thermostat, put the component into the opening in the duct casing, and restore the wires to the thermostat terminals.
- Now that you’ve completed replacing the faulty cycling thermostat, secure back the large, rear panel, and connect your dryer back in.
- Hold a pile of wet clothes and put them into your dryer in order to examine your newly repaired appliance.