Three Easy Ways Of Adjusting The Sliding Glass Door Rollers
With the passage of time, sliding glass doors can begin to stick, stop, or become very difficult to move. The most common reason behind this is that the dirt assembles on the rollers or the indented tracks that they sit in. However, it is very easy to repair or fix the sliding door in order to make it move smoothly again. With the help of a screwdriver, enhance the height of the rollers till the door glides easily along with a full range of motion. If in case you think that the dirty rollers are the main reason for the problem, then get rid of the door from the tracks and clean them with the help of rubbing alcohol.
Way 1: Changing The Position Of The Rollers
- Find The Adjustment Screws On The Lower Edges Of The Door: The majority of the sliding glass doors consist of two sets of rollers, one on each side of the base of the door. You can change the height of these rollers by examining the adjustment screws, which are adjusted into slots on the door's outer edges, upright with the rollers themselves.
- Use A Screwdriver To Turn The Screws And Move The Rollers Up Or Down: On most occasions, rotating the screws anticlockwise will elevate them, while rotating them clockwise will lower them. The main aim is to get them sitting ideally flush with the track.
- Continue Adjusting The Rollers Until The Door Glides Smoothly: It is possible that you may have to make few attempts before you get the door rolling without resistance. Once you are done, the door should be sitting ideally level on the track, and there should be an identical amount of space betwixt the door and the track on both the top and base.
Way 2: Cleaning The Rollers
- Retract The Adjustment Screws Fully To Remove The Door From Its Track: Find out the adjustment screw slots on the bottommost side edges of the door and with the help of a screwdriver, turn the screws anticlockwise as far as they will go. This, as a result, will lower the rollers thoroughly. Grasp either side of the door and with utmost care guide the upper edge out of the top track before raising the lower edge out of the base track.
- Place The Door On A Flat, Stable Surface: As soon as you have removed your door, move it over to a countertop, workbench, crafting table, or pair of sawhorses. To set the door down will let you work on the rollers blocked without caring too much about the door falling over or becoming damaged unintentionally.
- Pry Out The Roller Units With Your Screwdriver: Now, rotate the adjustment screws all the way to the right in order to fully extend the rollers. Then, squeeze the tip of the screwdriver into space betwixt the first set of rollers and the doorframe and then raise the handle smoothly in order to persuade the entire construction out. Replicate the same process with the rollers on the opposite side of the door.
- Wipe The Rollers Clean Using Rubbing Alcohol: Dip a cotton ball or the ragged corner in the alcohol and use it in order to polish the eliminated rollers. Make sure to concentrate on those areas that show indications of heavy grime or discoloration. Make your cleaning pad wet again with fresh alcohol before moving forward to the second set of rollers.
- Force The Roller Units Back Into The Channel On The Underside Of The Door: Arrange the top of each unit with the opening and press directly upon them smoothly in order to snap them back into place. As soon as they are secured, rotate the adjustment screws on the bottommost edges of the door all the way anticlockwise in order to put them back in their fully withdrawn position and prepare the door for reinstallation.
- Guide The Door Back Into Its Track, Starting At The Top: Line up the topmost edge of the door with the inner part of the top track and move the bottommost edge forward till it rests up against the base track. Lift up on the door and shift the bottommost edge into the base track, then set it down smoothly.
Way 3: Maintaining The Track
- Scrub The Entire Track With A Wire Brush: Slide both doors to one of the ends of the track in order to leave the opposite half revealed. Move your wire brush along the inner part of the track, ensuring to work the bristles deep into every crack, crevice, and contour. As soon as you finish cleaning the first half of the track, drag both the doors over to the other end and advance over the second half.
- Vacuum Or Wipe Up The Loose Debris: As soon as you have effectively loosened all of the dirt blocking up the track, get a shop vacuum and pump it up to remove the mess. If in case a vacuum handy is not available, make a clean cloth wet and squeeze out the excess water so that it's just moderately damp, then use it to pick up the debris by hand.
- Lubricate The Track With A Dirt-repelling Silicone Spray: Place the nozzle of the spray can 3–4 inches away from the track and run it gradually from one end to the other while taking hold of the spray button. Coat the track with the help of a thin, even layer of lubricant, before cleaning up any excess lubricant surrounding the floor, with the help of a folded paper towel.